Learn More, fire Detection Systems, multi-level fire detection systems planned and products installed by the manual best.
14 bypassing zones This key allows you to temporarily by-pass zones of your manual choice prior to arming your panel.
Full access allows the alarm User to display manual and change all access codes, change the panel time date, change telephone numbers and initiate Walk-test mode.This feature is a remote control facility which allows valid users to access the panel via a standard touch tone telephone and check or change the Arm/Disarm status of each of the areas, operate each of the eight outputs or turn on an optional Microphone.With the optional voice board fitted you can phone your home to check or change the status of any output using the keys on your phone.View memory mode memory display mode The alarm panel has an event memory which stores the most recent events (up to 127).To Disarm Stay Mode press; stay alarm Area A,B or both, armed LED s will turn OFF or code manual enter Area A,B or both, armed LED s will turn OFF.Security Cameras, monitor or surveill with high-quality cameras.When using the LED keypad the Panic alarm can be generated by either the single Panic button or by the simultaneous operation of two buttons.If so, I strongly encourage you to call Advance Alarms!On terminating Walk-test mode the test results are put into the memory buffer so they can be viewed at a later time.For example to program User # 3 with a code 2580, key in the following sequence: program 3 enter 2580 enter (If there is an existing code already at that address it will be flashed back on the keypad display.If Area A is Armed then the Armed message will be sent, if Disarmed then the Disarmed message will be sent.Entering the new code will delete the old and the new code will be flashed back to you).We have used them for 25 years we have always had top-notch service.Introduction 4 About your Alarm 4 operating your alarm 5 General Information 5 Arming the Alarm 5 Disarming products the Alarm 5 Arming in Stay Mode 6 Disarming Stay Mode 6 Bypassing Zones 7 Manual Panic, Medical Fire Alarms 8 Resetting Alarms 8 programming your alarm.The events include all alarm events, all system events such as mains failure, etc as well as arming by Area. To turn on the optional Microphone (only available if the Voice Board is fitted) you must enter in the appropriate code followed by the * button.
To arm Stay mode press; stay Area A,B or both, armed LED s will flash or Area A,B or both, armed LED s will flash.
To Disarm the full alarm press; code enter Area A,B or both, armed crack LED s will turn OFF.This allows you to select whether you wish the full Stay Mode to Arm with or without delays every time you arm this mode.Following the display of current system alarms the panel will then sequence through the 127 historical memory events starting at the most recent event.This process will be repeated 4 times before hanging up if no valid code is received.The panel has three different Arming modes and the methods of Arming are detailed above.The Alert 8D can communicate with monitoring stations or call you at work, on your cell phone or your pager to warn of intruders.In the example above as you press 1, service the display will show 01, then if you enter 5, the display will show 01 05 on the display and finally as you enter 8 the display will show all three numbers on the screen.Below you will find PDF copies of User Manuals for many popular control panels.The controller will support an 8 LED keypad missing or the more sophisticated LCD (liquid Crystal Display) keypad. 8 13 9 again will turn the output number being displayed off, indicating the output is now off.
Event type indication device indicator status activation Zones 1-8 LED's 1-8 exclude Zones 1-8 ready/excl LED's 1-8 detector tamper (short circuit) full detector tamper (open crack circuit) Zones 1-4 Zones 5-8 trouble LED's 1-4 trouble LED's 5-8 cabinet tamper Cabinet or Satellite Siren trouble LOW battery Controller.
The single button disarm of stay mode indicated above is a programmable option so you will need to check with your installer how your system has been configured.
To start Walk-test mode while in client mode press; program 627 enter (The keypad buzzer will beep at 1 second intervals) Next trigger every detector connected to the panel then return to the keypad and all of the zones that were triggered will be displayed.
The events are displayed with the most recent event shown first and subsequent events following in descending order from newest to oldest.
Once Stay mode has been Armed, the normal exit arrowhead alarm products old manual delay will apply and if a zone is triggered the normal entry delays will also apply.